How to program multiple remote units at one installation.
- Prices/Polices
- Installation Manuals
- Brochures / Literature
- Log Set Compositions
- Bromic Patio Heaters
-
Solaire Infrared Grills
Solaire Training Solaire Portable Infrared Grills Solaire 27XL Solaire 42 Solaire Side Burners Solaire Island Accessories Solaire Accessories Solaire 21 Solaire 36 Recipes Testimonials Solaire 27 Solaire 30 Solaire 56 Solaire Accent Solaire Demo Program Solaire Warranty Solaire 21XL Solaire 56T Unboxing - What's Inside Solaire "How To" Videos
- Vented Gas Logs
- Chillbuster Vent-Free Gas Logs
- Alterna (FireBalls, FireStones, FireGlitter)
- Electronic Ignition Systems
- FirePits
- Regulatory Issues
- Google SketchUp Models
- Testimonials
- Featured Articles
-
Prices/Polices
-
Installation Manuals
-
Brochures / Literature
-
Log Set Compositions
-
Bromic Patio Heaters
-
Solaire Infrared Grills
-
Vented Gas Logs
-
Chillbuster Vent-Free Gas Logs
-
Alterna (FireBalls, FireStones, FireGlitter)
-
Electronic Ignition Systems
-
FirePits
-
Regulatory Issues
-
Google SketchUp Models
-
Testimonials
-
Featured Articles
Q: How do I program two or more remote systems to work in the same space?
A:
- Clear all the codes from the control module or remote receiver. Slide the REMOTE/OFF switch on the control module or remote receiver to the OFF position on all units except the one you are currently trying to program.
- Slide the REMOTE/OFF switch to the remote position, press and hold the LEARN button for 10 seconds and then release it. Once released, an audible alert of three (3) long beeps in succession should be heard. This will signify that all security codes in the module / remote receiver have been cleared.
- Once the codes have been cleared, with the switch in the remote position, press and immediately release the LEARN button (a single beep should be heard) and then immediately after releasing the learn button, press and hold the ON or OFF button on the remote to send a signal. If the code has been successfully accepted there will be a series of four (4) rapid beeps.
Test the unit to ensure it is operating properly. If it is, turn remote switch to OFF and proceed to the next unit and repeat the procedure above.
Be sure upon completion of “learning” each unit to slide the remote switch to the OFF position and move on to the next unit complete. - Once you have completed this process
Featured articles
- 2024 MSRP Price List for Rasmussen Gas Logs, Alterna Contemporary Gas Fires and Chillbuster Vent-free log sets. Effective September 5, 2023
- 2024 Solaire Retail Price List, PDF and XLS format, effective March 20, 2023
- 2024-2025 Bromic MSRP Price List effective October 18, 2024
- How to light the pilot on your gas log set - general instructions
- #1 Vent-Free Issue - Nuisance Shutdown (or difficulty lighting) ODS Pilot
- I can't find replacement parts for my Rasmussen Gas Log, Solaire Grill or Bromic Heater - what should I do?
- General FirePit Guidance
- Solaire Ignition Systems Replacement Parts Matrix and List
- If my infrared burner pops, what can I do?
Popular Articles
- 2024 MSRP Price List for Rasmussen Gas Logs, Alterna Contemporary Gas Fires and Chillbuster Vent-free log sets. Effective September 5, 2023
- 2024 Solaire Retail Price List, PDF and XLS format, effective March 20, 2023
- How to light the pilot on your gas log set - general instructions
- Adding Logs to a Vented Gas Log Set
- Alterna Vent-free (FireBalls, FireShapes, FireStones) Instruction Manual
- Rasmussen Vented Gas Logs Brochure
- Platinum Gas shuts down after a short time
- I can't find replacement parts for my Rasmussen Gas Log, Solaire Grill or Bromic Heater - what should I do?
- I want to convert my vent-free gas log from one gas type to another